Battery power is a critical component in the overall performance of a boat for any activity on the water. From cranking up your outboard to operating integrated digital technologies and marine electronics, not much happens without a reliable source of ...
Basic upkeep for FourStroke outboard motors by Joe Balog.
Whether you outfit your rig with a TwoStroke or FourStroke outboard depends on the type of boat you’re running and what your performance needs are on the water. What’s much more cut and dry is the difference in routine service schedules between the two. If you’re considering a FourStroke and want to learn more about how to keep it performing optimally, whether your maintenance is done at home or by a professional, the steps outlined here should help out. We consulted members of the service crew at Toho Marine and Outdoors in St. Cloud, Fla., one of the country’s largest bass boat dealers, for the basics. Luckily, there are some industry standards (and rough guidelines) to follow when it comes to FourStrokes, but some of the specifics vary by make and model. If you decide to tackle it yourself, you’ll want to consult your dealer to make sure you’re following the proper maintenance procedures. And, it’s never a bad idea to simply rely on the dealer to do the maintenance for you. If that’s the route you go, you’ll understand the basics and know what services are being provided after reading this.
Change Engine Oil
If your new FourStroke has been broken correctly (according to Mercury recommendations) and operated for a few months under normal bass fishing conditions, the first maintenance usually occurs at the 100-hour mark. At that time, the engine oil and oil filter should be changed. Only use factory-recommended parts and lubricants such as Mercury Precision Parts. Although FourStroke engines perform similar to, say, an automobile, their needs are drastically different. For example, the oil must be able to withstand extended high RPM. Changing oil is simple. A drain screw is located on the lower gearcase. A special wrench may be needed for the oil filter located beneath the cowling, but it, too, can be easily removed and replaced. Don’t over-tighten when you replace it, and refill with the appropriate amount of oil.
Change Gear Oil
Along with an engine oil change, owners should also change gear oil at 100 hours. The drain and vent screws for this may be located on the lower unit, or possibly behind the prop. In any case, both must be removed to allow all the gear oil to drain. Check the oil for any discoloration (milky means water has entered the gear case) or metal pieces. The drain screw is also magnetic; check it for shavings that could indicate a gear problem. When refilling, gear oil must be pumped back in through the drain hole until it comes out the vent. Wait five minutes and pump a little more in to ensure it’s filled to capacity.
Change Fuel Filters
Fuel filters require initial 100-hour maintenance as well. Large four-stroke outboards include a fuel/water separator filter in the bilge area of the boat. This can be easily changed and should be during this initial service. The Mercury Verado also includes an additional pressurized filter that should be serviced by a dealer, but not until 300 hours.
Usually, after one year, it’s time for the outboard’s second scheduled maintenance. At this point, engine oil and filter, gear oil, and fuel filters should be changed again. In addition, the water pump should be inspected, and the impeller should be changed by the dealer (while the impeller may be in good shape, simple pump inspection requires substantial labor cost, so the part is changed for preventive purposes). In addition, spark plugs should be inspected and changed as needed. Good plugs will have a bronze coloration and sharp edges. Additionally, some dealers such as Toho Marine will perform further tests as part of their regular 100-hour service, including a computer diagnostic to check for codes that might indicate operating errors, and make sure the motor is firing efficiently. Further service also includes a compression check to ensure there’s no advanced carbon build-up or ring problems within the motor. As discussed, check your user manual for recommended 300-hour inspections and filter changes, as well as belt service at 1,000 hours.
A number of other service items can reduce headaches on the water:
1. Use fuel additives whenever possible, and stabilizer when needed, to reduce carbon build-up and fight the problems created by ethanol.
2. Fight corrosion on battery terminals with terminal cleaner.
3. Spray down the cowling seal with a silicone spray to keep it supple and watertight.
4. Visually inspect the power trim and tilt rams and seals for any leaks, and retract the rams all the way in during extended periods of non-use.
5. Each spring, inspect the cooling system outflow hole on the side of the motor to ensure it’s not clogged.
6. Finally, the best tip for any of today’s outboards: Buy gas at a busy station, and do not allow it to sit in your tank for more than a few months.